七麦数据

• Added to the Micro Brain2 FCU the management of the B-Aux3 channel on the CH4 connector to be able to control buzzer activation, retractable landing gear, lights, winch, smoke, etc. etc. via PWM signal
• Added handling of the new SKY telemetry parameter introduced by Spektrum with the November 21 AirWare update
• Introduced minor changes in the parameters of the "BEGINNER" flight style so that it can also be used satisfactorily in scale models, and added some information about scale models in the instructions
• Until panels 1 through 6 of the Wizard are completed, the servo outputs remain off so that panels prior to 7 and especially panel 5 can be configured correctly without being affected by servo movements
• In model with tail motor, to facilitate the tail setup minimum, zero and maximum, now when check mode is active (EG in panel 9 of the Wizard) tail motor can run also if main throttle is at zero
• Improved in software matching of the actual manageable and working functions of the old Brain and Micro Brain flight controllers
• Added “Cancel” to the “change language” confirmation message
• Added and improved some functions used to be able to provide a better remote assistance
• Changed some instructions, some tooltip, some labels in the app and also in the Integrations to be clearer
• Revised French instructions
• New version of the document “README_for_ESC_datas_log_and_telemetry.pdf” (+ELRS)
• New version of the document “README_for_OpenTX_EdgeTX_integration_for_BRAIN.pdf” (+TBS)
• New version of the document “README_for_Spektrum_Integration.pdf” document
• Improvements / optimization / compression / size reduction / code speedup

• Added the telemetry decodify of OMP ESC
• Implemented Forward Programming Integration for those who have Spektrum telemetry receivers on their models but have switched to using transmitters with OpenTX / EdgeTX operating systems and Multi Module Radio frequency. An LUA app will be released later
• Corrected the calculation of vibration frequencies with some production batches
• Added in apps and integrations to the list of adjustable parameters via Dials "TAIL: Proportional Gain" to simplify life to users who have set tail gain to "Is set in software."
• Modified the window for Bluetooth Configuration so that it can also contain longer texts (French)
• Changed some labels in the app and also in the Integrations to be clearer (EG: “VSpeed” to “Vertical Speed”)
• Lowered the automatic RPM drop when mAh Max Usage is exceeded from -18,75% to -12,5% for low main rotor speed flyer
• When mAh Max Usage is set at maximum (7000mAh) the function is totally disabled
• Raised the “Min V to Go” threshold from 3.82V to 3.88V
• Added in page 1 of the Wizard the “Radix” brand in the “Main Blades” and “Tail Blades” lists
• Added in page 1 of the Wizard the “AGF B53BHP-V2” servo in the “Cyclic Servo” list
• Added in page 1 of the Wizard the “HiTec HSG-8315BH” servo in the “Tail Servo” list
• Added in page 1 of the Wizard the “FullPower” brand in the “Power Supply Type” list
• Added in page 1 of the Wizard the “FlySky” brand in the “Transmitter Brand” list
• Made visible and operable in the telemetry selection dropdown the "DISABLED" item that was already displayed with the old flight controllers now also with the new flight controllers
• Although the confirmation prompt "Are you sure Y/N" is present, some users still reset by accident. For this reason moved to the bottom of the command list in the File menu the command "Reset to factory defaults ..."
• More diagnostic information saved in the configuration files
• Used and updated version of the Compiler
• Changed some instructions, some tooltip, some labels in the app and also in the Integrations to be clearer
• Revised French instructions
• New version of the document “README_for_OpenTX_EdgeTX_integration_for_BRAIN.pdf” (+TBS)
• New version of the document “README_for_ESC_datas_log_and_telemetry.pdf” (+ELRS)
• New version of the document “README_for_Spektrum_Integration.pdf” document
• Improvements / optimization / compression / size reduction / code speedup

• Crossfire channel reception up to 16CH (with ELRS and Packet Rate 333Hz Full)
• New Brain2Crossfire.zip version of Crossfire Integration package (Release Notes inside) that now other than TBS work also with ELRS External Module. Note: this version of the LUA app work only starting from this new firmware and for both TBS and ELRS external modules
• Added the new "High Vibrations" Event that is triggered if Global Vibrations continuously exceed 200% for at least 4 seconds. Even if the Global Vibrations continue to remain above 200% the event is not repeated until 2 minutes have elapsed
• In panel 3 updated the F.Port protocol icon
• In panel 12 of the Wizard moved the section "Sensor Input:" right after the first section "Setup Throttle Out & RPM reading:" since the two sections are related to each other
• Swap the positions of panels 11 and 13 of the Wizard with each other
• Clarified, completed, improved and updated some instructions and some message boxes
• Changed some labels in the app and also in the Integrations to be clearer (EG: “VSpeed” to “Vertical Speed”)
• Revised French instructions
• New version of the document “README_for_OpenTX_EdgeTX_integration_for_BRAIN.pdf” (+TBS)
• New version of the document “README_for_ESC_datas_log_and_telemetry.pdf” (+ELRS)
• Improvements / optimization / compression / size reduction / code speedup

• Improvements, changes, and corrections to previous version 3.4.100 as per user suggestions and reports
• Added the management of new Brain2/iKon2 batch
• Revised the routine of “Tail Motor RPM2” parameter to be able to record higher speed
• Added the checkbox for VARIO telemetry also in ADVANCED
• In Spektrum Integration added the checkbox for VARIO telemetry and the loggable parameters “Rel.Altitude” & “VSpeed”
• In Graupner Integration added the checkbox for VARIO telemetry and the loggable parameters “Rel.Altitude” & “VSpeed”
• New version of “Brain2Jeti.zip” integration files (release notes inside zip file)
• New version of “Ethos_Integration.zip” files (release notes inside zip file)
• New version of “Brain2OpenTX-EdgeTX.zip” Integration for Horus transmitters (release notes inside zip file)
• Added the actual software version on the top of the firmware update window
• Changed title of the panel 3 of the Wizard from “Receiver Selection” to “Receiver Protocol Selection”
• Revised some title of Wizard to better understand which are mandatory or optional setup (for simplified and expedited setup)
• Added to the description of Basic telemetry parameters logged “RPM2” & “Ext PWM”
• Changed the description of the loggable parameter “External PWM Input” to “Ext. Std PWM Input” to make it clearer that are expected impulses with 1520uS (Std.) center pulses and not impulses with 760us center pulse
• Revised the instructions of the COUNTERS (Timers) section of the Wizard
• Revised French instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document (“Tail Motor RPM2 & PWM” section)
• Improvements/optimization/compression/size reduction/speed up of the code

• Improvements, changes, and corrections to previous versions when ESC telemetry is active with F.Bus protocol
• A new LUA app for Ethos version that now works also with F.Port protocol and S.Port+S.Bus protocol, display on top bar which is the Setup (1/2/3) active whose values are shown, and added in the list of diagnostic parameters selectable in page 11 (Diagnostic) also "Rel.Altitude" and "VSpeed"
• Added decoding of a Futaba SBS-01A sensor connected to the S.Bus2 line to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added decoding of a Robbe “Vario Sensor” connected to the S.Bus2 line to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added decoding of a Graupner “GPS” sensor connected to the telemetry line on CH3 to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added decoding of a FrSky “VARIOMETER SENSOR” sensor connected to the telemetry Smart.Port on CH3 to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory
• Added the possibility of connecting a Jeti “Mvario2” sensor to SAT2 connector and decode the signal to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory also for non-telemetric receivers / protocols
• Added the possibility of connecting a Jeti “MALTI EX” sensor to SAT2 connector and decode the signal to be able to log "Altitude" & "VSpeed" parameters in the Flight Log memory also for non-telemetric receivers / protocols
• Added in the “Telemetry Input” subpanel a new “Vario” checkbox
• Now with Windows app, using the left Ctrl key of the keyboard it is possible to update the Events windows, start/stop real time logs, start/stop real time vibrations
• Added some new functions for diagnostic purpose loading an user mtr configuration file (Servo Voltage, CPU temperature, etc)
• Revised French instructions
• New “README_for_Ethos_Integration_for_BRAIN.pdf” document
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document with a new page for variometers
• Improvements/optimization/compression/size reduction/speed up of the code

• Improvements, changes, and corrections to previous version 3.4.084 when telemetry is active with F.Bus & F.Port protocol
• Added "Altitude" & "VSpeed" to the loggable parameters. The first sensor activated is the FrSky ADV VARI sensor to be connected on the F.Bus
• Updating the Events screen can now also be done using the left "Ctrl" button on the keyboard
• On page 1 of the Wizard (page that opens after each update when running the Windows app) the Internet connection status has been moved to the first position and is highlighted in red if there are problems with connection or no connection to the Internet
• In the firmware update window, added the sentence explaining that a stable Internet connection is required for the update
• Increased the number of retries during firmware updates when the Windows app connects to our update servers
• As user request, reduced the minimum values for Speed 1, 2, 3 on the Governor page from 1000rpm to 800rpm
• In ADVANCED, Common tab, Servos, the "Tail Motor Driven" selection is now only possible for tail servo 4
• Revised French instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document

• Improvements, changes, and corrections to previous version 3.4.081 as per user suggestions and reports
• Revised French instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document

• Added Crossfire (416.666bps) with telemetry decoding. Telemetry is transmitted to RX from CH3 connector and channels transmitted by RX are received from SAT1 connector
• Added the FrSky F.Bus icon (460.800bps) in panel 3 “Receiver Selection (Input)” of the Wizard
• Added FlySky i-Bus protocol (with telemetry) automatic recognition and decoding when the multiprotocol icon is selected
• Spektrum protocol SRXL2 can now work at higher speed (400.000bps) if all devices connected to the SRXL2 bus can rut at this speed. This permits a lower latency in the commands.
• Now regardless of whether the flight controller's governor is used or not, when the model blade length is selected in Wizard panel 10, the governor's Speed1/Speed2/Speed3 values are raised to the typical RPM values for the model size (low for large models high for small models)
• In panel n°1 “General Instructions” of the Wizard, "SAB Goblin 580 Nitro" has been added to the model selection dropdown list
• Added in panel 1 of the Wizard the item “Transmitter Mode” for a better support and statistic purpose
• In panel 5, the "Tail Gain" signal slider changes to blue color if during subsequent tail setup it was decided not to use a radio channel to control tail gain but to select the "Is set in software" checkbox. This is because in this case it will be more obvious that the tail gain slider position in panel 5 and controlled by the transmitter, cannot modify the tail gain
• Added three traffic lights in the title bar of Wizard panel 5 that indicate in real time whether the receiver and/or satellite 1 and/or satellite 2 are working or not working or whether the signal is intermittent
• Increased in panel 12 of the Wizard and in Advanced the maximum value of “Pulses for rotations” from 20 to 25 (for the new DirectDrive motor bundled in RAW 420 with 21 pairs of magnets)
• Added under “Help” menu the new files for Integration on FrSky transmitter using the new ETHOS OS (Tandem20 / 20S, Tandem18 / 18S, Horus X12S-ISRM, X10 / X10S Express)
• Released a new updated version of the Brain2OpenTX.zip file (see ReleaseNotes.txt)
• Released a new updated version of the Brain2Jeti.zip file (see ReleaseNotes.txt)
• Revised Spektrum Integration
• Revised Graupner Integration
• Added for better diagnostic purpose the following purple ESC Events:
220 "ESC: Low voltage protection" For YGE, Scorpion, Kontronik, HobbyWingV5
221 "ESC: Over current protection" For YGE, Scorpion, Kontronik, HobbyWingV5
222 "ESC: Over temperature protection" For YGE, Scorpion, Kontronik, HobbyWingV5
223 "ESC: Input throttle is not at 0% position" For HobbyWingV5
224 "ESC: Motor locked protection" For HobbyWingV5
225 "ESC: Throttle Signal loss protection" For HobbyWingV5
226 "ESC: Abnormal input voltage" For HobbyWingV5
227 "ESC: ESC lack of one phase" For HobbyWingV5
• Many additions, changes and improvements in the data saved within the configuration files, Event files and recorded Logs files, and in the management of update server data so that we can do more in-depth analysis on the files received from users and offer better support and diagnosis and remote assistance
• Revised French instructions
• Some revision of icons, connections diagram, names, titles, labels, units and instructions
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document
• Improvements/optimization/compression/size reduction/speed up of the code

• Added (only for combustion models that have a clutch: “Is Electric” not selected), the new “Failsafe Idle value” that prevents combustion engines from shutting down in the event of short radio signal interruptions (Fail Safe)
• Added decoding of the new Platinum V5 protocol of Hobbywing (used for now only on new Platinum V5 150A)
• Added for deeper diagnostic purpose purple events for the following YGE, Kontronik, Scorpion, Platinum V5 errors: “ESC: Low voltage protection”, “ESC: Over current protection”, “ESC: Over temperature protection”
• Added decoding of the new F.Bus protocol used with the new FrSky ETHOS transmitters. For now selectable only from the protocols drop-down menu in: ADVANCED => Common => Receiver
• Added a power supply voltage check that prevents the firmware update process from starting if the voltage is too low. This is because by analyzing the external event memory of the Flight Control Units that came back with the processor ROM erased and/or altered, we have seen that in these returns the events "Voltage 4,3V" are always present
• Added in the Firmware update progress windows the red phrase “Do not disconnect and do not remove power and do not close the program until the update process is finished !!!”
• Added a new message box “No Firmware selected” that appear if in the Firmware selection no firmware was selected before click on “Upload Now”
• Added the orange background that warns that the configuration of one of the Wizard panels has not been completed also in panels 9 (Tail Rotor Setup), 10 (Blades Size) and 13 (Flying Style)
• Added in the Bluetooth configuration windows the phrase “Avoid using “special” characters for NAME but use only letters and numbers.” in order to eliminate the problems encountered by some users
• Increased the minimum values for Speed 1, 2, 3 on the Governor page from 500rpm to 1000rpm following problems encountered by some users with some Speed set at 500rpm and with the model losing altitude too quickly
• If "Min V to go" has been set to a number of Lipo Cells greater than 2, but the ESC telemetry is not working due to misconfiguration or miswiring, the throttle will not lock as when there is no active ESC telemetry reading the battery voltage.
• Added in panel 14 (Final checks) an explanation of elevator swashplate movements
• Fixed the Fail Safe behavior with R3XXXXSB / R2XXXXSB receivers (FHSS) when telemetry is used using S.Bus2
• F.Port & F.Port2: eliminated occasional servo movements during Logs download
• Some revision of names, titles, labels, units, instructions & menu order (English and Italian)
• New version of “README_for_ESC_datas_log_and_telemetry.pdf” document
• Improvements/optimization/compression/size reduction/speed up of the code

• Added to the 11 Jeti telemetry transmitted values selected in the “Parameter Setup” tab of DIAGNOSTIC, also the “Log Parameter 12” value “Global Vibrations”. If an ESC is selected in “Telemetry Input” of panel 12 of the Wizard, are also transmitted “ESC Battery Voltage”, “ESC Battery Current”, “ESC Battery Used”, “ESC Battery Ripple”, “ESC Power Output”, “ESC LS RPM”, “ESC Temperature 1 (°C & °F)” values. If Hobbywing or Jive Pro or YGE are selected also “ESC Temperature 2 (°C & °F)” are transmitted. If Jive Pro or YGE are selected also “ESC BEC Current” is transmitted. A New AUTO Discover is not required, but all new parameters must be Added in “New Displayed Telemetry” if you want to see it
• Added in the File menu the “Reset Logs to default” command
• With Tandem Rotor models, by giving elevator commands the pitch increase of one rotor is greater than the pitch reduction of the other rotor to achieve a behavior of Tandem Rotors models more similar to that of single rotor models
• Rewritten, simplified and reduced size of Firmware unifying some similar routines used for S.Port+S.Bus, F.Port, F.Port2
• If FrSky Neuron ESC’s telemetry signal is connected to the S.Port bus via an “Y” cable the ESC telemetry is recognized and can be recorded in Flight Controller logs
• Added to the OpenTX the “PowerOut” pwm value (0-100%) with the sensor name “1000” (like for global vibrations, there are no predefined sensor for this kind of value in actual OpenTX versions)
• Added the Event “Voltage > 8V4” as a warning that the receiver and/or servos may be damaged at such supply voltages, and that the BEC regulator may have failed
• Added the Event “Flight Count increased” to better understand if that Event group is related to a real flight or to a bench test / ground test. Note: the “Flight Count” value in COUNTER section may not correspond to the number of Recorded Logs due to possible bench logging
• Now in all “Integrations” “Pitch Out Max:” is displayed correctly also if “Reversed Pitch” is selected
• Now using OpenTX S.Port + S.Bus protocol and connections, no more “sensor lost” message happen for VFAS sensor
• Restored the filtering of the RPM signal used by the Governor to the highest filtering values used prior to the FW versions 3.4.013 because of problems with some ESCs (Castle Creation) with high noise on RPM wires
• Starting with firmware 3.4.XXX the Spektrum Binding via Software and/or via Hardware does not work with SRXL2 receivers and the on-board bind button of the SRXL2 receivers must be used. Fixed
• Now also with the F.Port2 protocol the secondary receiver connected via “S.Bus In” to the main receiver is correctly working
• Values of Exponential’s that cause a slight change in the output values now work only for Pitch channel and not for all the other channels
• Now if the unit still has the factory firmware, the configuration software won't start if you don't update the FW to a valid version, as explained in the instructions the units must not be configured and must not fly with factory firmware
• Now the parameter selection dropdowns of the Windows configurator are opened by clicking in any area of the dropdown instead of the small button on the right as before
• In panel n°1 “General Instructions” of the Wizard, “RadioMaster" has been added to the transmitter drop-down list and "Oxy 5 Nitro" has been added to the model selection list and at the request of some users "Zigsaw AYA" has been added in the blade’s selection dropdown
• In panel n°3 “Receiver Selection” of the Wizard, in the Multiprotocol icon and lateral instructions the Spektrum SRXL2 protocol has been moved to the first position so that it can be more easily and quickly viewed by those who often select by mistake the Spektrum SRXL protocol used only by 4649T receivers
[MORE...]